AdvantaClean of West Columbia Case Studies

Schedule an Appointment

To request a service call you only need to fill out the form below. We will contact you via phone, email, or text to confirm the best appointment time. You will receive an email confirming your service request.
or Call Now (877) 800-2382

Success Stories

Location: Spartanburg, South Carolina 29306

Problem: This commercial office building was flooded due to flash flooding.

Solution: Water was extracted, flood cutting was performed where needed, fans and dehumidifiers were placed to dry out the area in 3 days. Areas were cleaned with antimicrobial in order to prevent any microbial growth.

FloorFirst1.jpg FloodSecond1.jpg FloodThird1.jpg    

Location: Lancaster, South Carolina 29720

Problem: The home was built with the absence of a moisture barrier in the crawlspace, allowing vapor pressure from the ground underneath to cause humidity issues.

Solution: We installed a basic moisture barrier across the ground and was vapor taped at all of the seams. This allows no ground vapor pressure from the ground to penetrate the crawlspace air. Along with this, the vents were sealed off and a commercial grade dehumidifier was installed in order to keep humidity levels at or below 60%, this makes an environment impossible for mold to grow.


Location: Lancaster, South Carolina 29720

Problem: The homeowner was feeling ill due to the air quality in the home. The issue was in the crawlspace, where we found mold due to high moisture levels, vegetation and years of trash/debris.

Solution: The solution to the home owners issue was to perform a complete mold remediation of the crawlspace, remove vegetation and debris followed by installing a full encapsulation with a dehumidifier.


CrawlspaceMoistureFirst3.jpg CrawlspaceMoistureSecond3.jpg    

Location: Lancaster, SC 29720

Problem: Crawlspace had mold growth on joists and insulation due to high humidity.

Solution: The solution to this issue was to remove the contaminated insulation, remediate the mold, put back new insulation and install a full encapsulation with a dehumidifier.

MoldRemovalFirst4.jpg MoldRemovalSecond4.jpg    

Location: Boiling Springs, SC 29316

Problem: A small toilet plumbing leak, over time, lead to mold growing under the flooring, sink cabinet and drywall.

Solution: Set up containment remove sink cabinet, flooring, sub-floor and perform a 2ft flood cut around the bathroom. HEPA vacuum the area and treat with anti-microbial.

BathroomFirst5.jpg BathroomSecond5.jpg    

Location: Spartanburg, SC 29302

Problem: Due to humidity and standing water over time, mold began to grow on wood joists, sub flooring, and insulation. Homeowners felt allergy-like symptoms.

Solution: A removal of the crawlspace insulation, complete mold remediation and reinstall insulation.


Location: Spartanburg, SC 29307

Problem: High humidity and a broken pipe led to a mold issue in the crawlspace. This caused poor indoor air quality, buckling of hardwood flooring and a failed inspection.

Solution: Remediate the mold to the EPA standard, by removing the existing insulation, HEPA vacuuming all joists and subfloor, followed by being wiped down with an Anti-microbial, and then HEPA Vacuuming once again.

SpartanburgFirst7.png SpartanburgSecond7.png    

Location: Florence, SC 29501

Problem: Rehabbing commercial building, the coils on 3 units had never been cleaned.

Solution: Using our professional grade coil cleaning equipment, we were able to completely clean all dust and debris from coils. The unit worked much more efficient after our cleaning.



Location: Lancaster, SC 29720

Problem: Mold growth on walls/inside walls

Solution: Containment, negative air on the space, cut two feet of drywall passed where there is visible mold, HEPA vacuum and clean behind with anti-microbial, fog the area with anti-microbial and let air scrubbers run for 48 hours.


Location: Camden, SC 29020

Problem: Mold was present throughout the entire crawlspace, due to the high humidity and absence of a moisture barrier.

Solution: Pull all insulation, remediate mold, install a 15mil moisture barrier and reinstall insulation.


Location: Lancaster, NC 29009

Problem: For over six years a leaking roof in an abandoned doctor's office created a huge mold issue.

Solution: We remediated the mold by removing all affected drywall, flooring, insulation and ceiling. Our next step was cleaning of the entire air duct system, then fogged the entire building with an anti-microbial substance.


Location: Union, South Carolina 29379

Problem: Over time a leaking roof caused mold to grow on the ceiling.

Solution: We repaired the roof, set up a containment, and followed with full mold remediation of the space. The remediation included removal of the entire ceiling, some walls and cleaning the wood joists behind them. We finished by HEPA vacuuming and wiping with an antimicrobial.


Location: Waxhaw, NC 28173

Problem: High humidity in the crawlspace that leads to mold growth and moisture issues.

Solution: Remediate the mold, install the AdvantaSeal full encapsulation system, along with the installation of a dehumidifier.


Location: Florence, SC 29501

Problem: Water seepage coming in from the exterior wall over time, caused mold to grow on the interior wall.

Solution: We removed affected materials, remediated mold with antimicrobial and HEPA vacuuming. Next, we followed with setting up fans and dehumidifiers to dry out the wet areas.